Journal of Ocean Engineering and Technology (한국해양공학회지)

Korean Society of Ocean Engineers (한국해양공학회)
권호 표지

Evaluation of Characteristic for SS400 and STS304 steel by Weld Thermal Cycle Simulation - 1st Report : on the Mechanical Properties and Microstructure

용접열사이클 재현에 의한 SS400강 및 STS304강의 특성 평가 - 제1보 : 기계적 특성 및 조직

  • Ahn, Seok-Hwan (Shool of Mehanical Engineering, Pukyong National University) ;
  • Jeong, Jeong-Hwan (Graduate School of Materials Science and Engineering, Pukyong National University) ;
  • Nam, Ki-Woo (Division of Materials Science and Engineering, Pukyong National University)
  • 안석환 (부경대학교 기계공학부) ;
  • 정정환 (부경대학교 대학원 재료공학과) ;
  • 남기우 (부경대학교 신소재공학부)
  • Published : 2005.12.01
Download PDF
⟨ Previous Next ⟩

Abstract

The welding methods have been applied to the most structural products used in the automobile, ship construction, and construction. The structure steel must have sufficient strength of structure; However, the mechanical properties of the welded part changes when it is welded. Therefore, the stability or life of the structure may be affected by the changed mechanical properties. The mechanical properties of the welded part must be examined in order to ensure the safety of structure. In this research, the SS400 steel and the STS304 steel were used to estimate the mechanical properties of the HAZ by weld thermal cycle simulation. In this study, the materials were used to examine the weld thermal cycle simulation characteristic, under two conditions: the drawing with diameter of $\Phi$10 and the residual stress removal treatment. To examine the mechanical properties by the weld thermal cycle simulation, the tensile test was carried out in room temperature. The crosshead speed was lmm/min.

Keywords

References

  1. 마루젠주식회사 (1990). 용접.접합편람, 일본용접학회, pp 810-811
  2. 히라카와 켄지, 오오타니 히로오, 엔도 마사히로, 사카모토 하로오 (2002) 기계재료학, 조창서점, pp 52-165
  3. 세키구치 키치로, 요시무라 고로 (1980). 현대용접기술대계-용접과 재질(상), 산보출판, pp 235-260
  4. 스즈키 하루요시, 타무라 히로시 (1980). 현대용접기술대계-용접금속학, 산보출판, pp 51-81
  5. 방한서, 차용훈, 오율권, 노찬승, 김종병 (1997). '점열탄소성 이론에 의한 용접후열처리에 대한 수치해석', 한국해양공학회지, 제11권, 제1호, pp 113-123
  6. 안홍조, 이찬우, 이창희 (2001). 'C-Mn 구조용강 열영향부의 결정립 성장 거동 예측 모델링 ', 대한금속.재료학회지, 제38 권, 제6호, pp 841-850
  7. 엄기원 (1996). 최신용접공학, 동명사, pp 249-271
  8. 오세규, 남기우 (1983). '국산구조용강판의 수중용접성과 용접 강도 특성', 대한기계학회논문집, 제7권, 제3호, pp 263-269
  9. 이상기, 도재윤, 남기우, 강창룡, 이해우, 안석환 (2000). ,수퍼 2상 스테인리스강의 피로균열진전 특성에 미치는 미세조직의 영향', 한국해양공학회지, 제14권, 제2호, pp 66-70
  10. 이영배, 박정웅 (1999). 금속열처리원리, 문운당, pp 122
  11. 홍종휘 (1986). 금속재료, 보성출판사, pp 179-206
  12. Hannerz, N.E. (1985). Idealized Thermal Cycle for Weld Heat Affected Zone Simulation of Steel, Perdue Thermal Physical Property Handbook, Perdue Univ
  13. Welding Handbook (1976). Fundamentals of Welding, 7th Edition, Vol 1. American Welding Society