DOI QR코드

DOI QR Code

J-그루브를 이용한 인듀서의 캐비테이션 억제에 관한 연구

A Study on the Suppression of Cavitation in Inducer by J-Groove

  • 발행 : 2005.11.01

초록

Cavitation is the most serious problem in developing high-speed turbopump, and inducer is often used to avoid cavitation in main impeller. Thus, inducer is always operating in the worst .cavitation condition. If it is possible to control and suppress cavitation in inducer by some new device, it might be possible to suppress cavitation occurring in any type of pumps. The purpose of present study is to develop a new effective method of controlling and suppressing cavitation in inducer using shallow grooves, which is named 'J-Groove'. J-Groove is installed on the casing wall near the blade tip to use the pressure difference between high pressure region and low pressure region of the inducer in an axial direction. The results show that proper combination of backward-swept inducer with J-Groove improves suction performance of turbopump remarkably in the range of partial flow rate as well as designed flow rate. The rotating backflow cavitation occurring in the range of low flow rate and the cavitation surge occurring in the vicinity of the best efficiency point can be almost suppressed by installing J-Groove.

키워드

참고문헌

  1. Lakshminarayana, B., 1982, 'Fluid Dynamics of Inducers - A Review,' Trans. ASME J. of Fluids Eng., Vol. 104, pp. 411-427 https://doi.org/10.1115/1.3241874
  2. Japikse, D, 2001, 'Overview ofIndustrial and Rocket Turbopump Inducer Design,' Proc. CAV2001, Session B7.001
  3. Kurokawa, J., Saha, S. L., Matsui, J. and Kitahora, T., 2000, 'Passive Control of Rotating Stall in a Parallel-Wall Vaneless Diffuser by Radial Grooves,' Trans. ASME J. of Fluids Eng., Vol. 122, pp. 90-96 https://doi.org/10.1115/1.483230
  4. Saha, S. L., Kurokawa, J., Matsui, J. and Imamura, H., 2000, 'Suppression of Performance Curve Instability of a Mixed Flow Pump by Use of J-Groove,' Trans. ASME J. of Fluids Eng., Vol. 122, pp. 592-597 https://doi.org/10.1115/1.1287855
  5. Saha, S. L., Kurokawa, J., Matsui, J. and Imamura, H., 2001, 'Passive Control of Rotating Stall in a Parallel-Wall Vaned Diffuser by J-Grooves,' Trans. ASME J. of Fluids Eng., Vol. 123, pp. 507-515 https://doi.org/10.1115/1.1374214
  6. Tsujimoto, Y., Yoshida, Y., Maekawa, Y., Watanabe, S. and Hashimoto, T., 1997, 'Observations of Oscillating Cavitation of an Inducer,' Trans. ASME J. of Fluids Eng., Vol. 119, pp. 775-781 https://doi.org/10.1115/1.2819497
  7. Imano, A. and Hashijume, N., 2001, 'LE-7 Engine Turbo-pump and the Cause of Failure in H-II Rocket No. 8,' Turbomachinery (TSJ), Vol. 29, pp. 139-146
  8. Kamijo, K. and Yoshida, M., 1991, 'Experimental Study of LE-7 LOX Pump Inducer,' Trans. of the JSME (B), Vol. 57, pp. 4023-4028
  9. Fujii, A., Azuma, S., Yoshida, Y., Tsujimoto, Y., Horiguchi, H. and Watanabe, S., 2002, 'Higher Order Rotating Cavitation in an Inducer,' Trans. of the JSME (B), Vol. 68, pp. 1466-1473
  10. Tahara, H. and Manabe, A., 1984, 'Influence of Inlet and Outlet Angles of Inducer on Improvement in Suction Performance of Centrifugal Pump,' Trans. of the JSME (B), Vol. 50, pp. 2619-2624 https://doi.org/10.1299/kikaib.50.2619
  11. Bakir, F., Kouidri, S., Noguera, R. and Rey, R., 2003, 'Experimental Analysis of an Axial Inducer Influence of the Shape of the Blade Leading Edge on the Performances in Cavitating Regime,' Trans. ASME J. of Fluids Eng., Vol. 125, pp. 293-301 https://doi.org/10.1115/1.1539872
  12. Takamatsu, Y., Furukawa, M. and Ishizaka, K., 1978, 'Suction Performance Improvement of a Centrifugal pump by Helical Inducer,' Trans. of the JSME (B), Vol. 44, pp. 960-969 https://doi.org/10.1299/kikai1938.44.960
  13. Takamatsu, Y., Furukawa, M., Ishizaka, K. and Nikamoto, H., 1978, 'Outlet Flow of a Planar Helical Inducer,' Trans. of the JSME (B), Vol. 44, pp. 950-959 https://doi.org/10.1299/kikai1938.44.950