STUDY ON THE IN-CYLINDER FLOW CHARACTERISTICS OF AN SI ENGINE USING PIV

  • LEE S.-Y. (Department of Mechanical Engineering, RIMT, Pusan National University) ;
  • JEONG K.-S. (Department of Automotive Engineering, Jinju International University) ;
  • JEON C.-H. (Department of Mechanical Engineering, RIMT, Pusan National University) ;
  • CHANG Y.-J. (Department of Mechanical Engineering, RIMT, Pusan National University)
  • Published : 2005.10.01

Abstract

The tumble or swirl flow is used to promote mixing of air and fuel in the cylinder and to enlarge turbulent intensity in the end of the compression stroke. Since the in-cylinder flow is a kind of transient state with rapid flow variation, which is non-steady state flow, the tumble or swirl flow has not been analyzed sufficiently whether they are applicable to combustion theoretically. In the investigation of intake turbulent characteristics using PIV method, typical flow characteristics were figured out by SCV configurations. An engine installed SCV had higher vorticity and turbulent strength by fluctuation and turbulent kinetic energy than a baseline engine, especially near the cylinder wall and lower part of the cylinder. Above all, the engine with SCV 8 was superior to the others in aspect of vorticity and turbulent strength. For energy dissipation, a baseline engine had much higher energy loss than the engine installed SCV because flow impinged on the cylinder wall. Consequently, as swirl flow was added to existing tumble flow, it was found that fluctuation increased and flow energy was conserved effectively through the experiment.

Keywords

References

  1. Chang, T. H. (2004). Experimental study on turbulent swirling flow in a cylindrical annuli by using the PIV technique. Int. J. Automotive Technology 5, 1, 17-22
  2. Chang, T. H. (2004). Experimental study on turbulent swirling flow in a cylindrical annuli by using the PIV technique. Int. J. Automotive Technology 5, 1, 17-22
  3. Cho, G. B., Jeon, C. H., Chang, Y. J. and Kang, K. Y. (1997). Characteristics of in-cylinder steady flow using PIV for different intake port geometries in a 4-valve gasoline engine. Trans. Korean Society Automotive Engineers 5, 5, 188-196
  4. Hacohen, J., Beltmont, M. R. and Ashcroft, S. J. (1994). Flame speeds in a spark ignition engine. SAE Paper No. 942050
  5. Jeon, C. H., Chang, Y. J. Cho, K. B. and Kang, K. Y. (1998). Effects of intake ports on in-cylinder flow and lean combustion in a 4-valve engine. SAE Paper No. 981048
  6. Lee, J. H. and Farrell, P. V. (1993). Intake valve measurement of an in engine using particle image velocimetry. SAE Paper No. 930480
  7. Lee, K. H., Lee, C. S., Lee, H, G.,Chon, M. S. and Joo, Y. C. (1998). Spatial analysis of turbulent flow in combustion chamber using high resolution dual color PlY. Trans. KSME 6,6,132-141
  8. Le Coz, J. F. (1992). Cycle-to-cycle correlations between flow field and combustion initiation in a SI Engine. SAE Paper No. 920517
  9. Melling, A. (1997). Tracer particles and seeding for particle image velocimetry. Meas. Sci. Technology 8, 1406-1416 https://doi.org/10.1088/0957-0233/8/12/005
  10. Park, J. H., Lee, N. H. and Choi, K. H. (1999). Analysis of in-cylinder flow fields using particle image velocimetry. Trans. Korean Society Automotive Engineers 7, 4, 46-53
  11. Ronnback, M., Le, W. X. and Linna, J. R. (1991). Study of induction tumble by particle tracking velocimetry in a 4-valve engine. SAE Paper No. 912376
  12. Son, J. W., Lee, S. H., Han, B. H. and Kim, W. T. (2004). A correlation between re-defined design parameters and flow coefficients of SI engine intake ports. SAE Paper No. 2004-01-0998