Journal of Mechanical Science and Technology

The Korean Society of Mechanical Engineers (대한기계학회)
권호 표지

High-Temperature Rupture of 5083-Al Alloy under Multiaxial Stress States

  • Kim Ho-Kyung (Department of Automotive Engineering, Seoul National University of Technology) ;
  • Chun Duk-Kyu (Department of Automotive Engineering, Seoul National University of Technology) ;
  • Kim Sung- Hoon (Department of Structural Engineering, Seoul National University of Technology)
  • Published : 2005.07.01
Download PDF
⟨ Previous Next ⟩

Abstract

High-temperature rupture behavior of 5083-Al alloy was tested for failure at 548K under multiaxial stress conditions: uniaxial tension using smooth bar specimens, biaxial shearing using double shear bar specimens, and triaxial tension using notched bar specimens. Rupture times were compared for uniaxial, biaxial, and triaxial stress conditions with respect to the maximum principal stress, the von Mises effective stress, and the principal facet stress. The results indicate that the von Mises effective and principal facet stresses give good correlation for the material investigated, and these parameters can predict creep life data under the multiaxial stress states with the rupture data obtained from specimens under the uniaxial stress. The results suggest that the creep rupture of this alloy under the testing condition is controlled by cavitation coupled with highly localized deformation process, such as grain boundary sliding. It is also conceivable that strain softening controls the highly localized deformation modes which result in cavitation damage in controlling rupture time of this alloy.

Keywords

References

  1. Anderson, P. M. and Rice, J. R., 1985, 'Constrained Creep Cavitation of Grain Boundary Facets,' Acta Metall., Vol. 33, pp. 409-422 https://doi.org/10.1016/0001-6160(85)90083-5
  2. Cane, B. J., 1982, 'Creep Damage Accumulation and Fracture Under Multiaxia1 Stresses,' in Advances in Fracture Research (Fracture 81), Vol. 3, pp. 1285-1293, Pergamon Press, Oxford, United Kingdom
  3. Dyson, B. F., 1976, 'Constraints on Diffusional Cavity Growth Rates,' Mater Sci., Vol. 10, pp. 349-353
  4. Dyson, B. F. and Leckie, F. A., 1988, 'Physically Based Modeling of Remanent Creep Life,' Mater. Sci. & Eng. A, Vol. 103, pp. 111-114 https://doi.org/10.1016/0025-5416(88)90557-5
  5. Eggler, G., 1989, 'The Effect of Long-Term Creep on Parameter Coarsening in Tempered Martensite Ferritic Steels,' Acta Metall., Vol. 37, pp. 3225-3234 https://doi.org/10.1016/0001-6160(89)90194-6
  6. El-Nasr, A. A., Mohamed, F. A., Earthman, J. C., 1996, 'High Temperature Rupture of an SiC Particulate Reinforced Al Composite Under Multiaxial Stress State,' Mat. Sci. & Eng. A, Vol. 214, pp. 33-41 https://doi.org/10.1016/0921-5093(96)10219-7
  7. Goel, A., Ginter, T. J. and Mohamed, F. A., 1983, 'Effect of Stress Reduction Ratio on the Stress Exponent and Subgrain Size in an Al-Zn Alloy,' Metal. Trans. A, Vol. 14, pp. 2309-2318 https://doi.org/10.1007/BF02663306
  8. Hayhurst, D. R., 1972, 'Creep Rupture Under Multi-Axial States of Stress,' J. Mech. Phys. Solids, Vol. 20, pp. 381-390 https://doi.org/10.1016/0022-5096(72)90015-4
  9. Hayhurst, D. R., Leckie, F. A. and Henderson, J. T., 1977, 'Design of Notched Bars for Creep-Rupture Testing Under Tri-Axial Stresses,' Int. J. Mech. Sci., Vol. 19, pp. 147-159 https://doi.org/10.1016/0020-7403(77)90074-1
  10. Henderson, J., 1979, 'An Investigation of Multi-Axial Creep Characteristics of Metals,' Trans. ASME, Vol. 101, pp. 356-374
  11. Huddleston, R. L., 1985, 'An Improved Multiaxial Creep-Rupture Strength Criterion,' J. Pressure Vessel Technol., Vol. 107, pp. 421-429 https://doi.org/10.1115/1.3264476
  12. Inoue, M. et al., 1998, 'Creep and Creep Rupture of Welded Joints of 5083 Aluminum Alloy Plates,' J. Japan Ins. Light Metals, Vol. 48, No. 10, pp. 479-483 https://doi.org/10.2464/jilm.48.479
  13. Isshiki, K. et al., 1997, 'A New Miniature Mechanical Testing Procedure: Application to Intermetallics,' Metal. and Mater. Trans. A, Vol. 28A, pp. 2577-2582 https://doi.org/10.1007/s11661-997-0015-8
  14. Jonson, N. L. and Earthman, J. C., 1994, 'Numerical Analysis of Primary Creep Deformation in a Novel Double Shear Specimen Geometry,' J. Testing and Evaluation, JTEVA, Vol. 22, pp. 111-116 https://doi.org/10.1520/JTE12643J
  15. Kim, H. K., Mohamed, F. A. and Earthman, J. C., 1992, 'A Novel Specimen Geometry for Double Shear Creep Experiments, J. Testing and Evaluation,' JTEVA, Vol. 19, pp. 93-96 https://doi.org/10.1520/JTE12540J
  16. Kim, H. K., Chung, K. and Chung, C. S., 1998, 'High Temperature Rupture Lifetime of 304 Stainless Steel Under Multiaxial Stress States,' KSME Journal A, Vol. 22. No. 3, pp. 595-602
  17. Nix, W. D. et al., 1989, 'The Principal Facet Stress as a Parameter for Predicting Creep Rupture Under Multiaxial Stresses,' Acta Metall., Vol. 37, pp. 1067-1077 https://doi.org/10.1016/0001-6160(89)90103-X
  18. Ridel. H., 1987, 'Fracture at High Temperatures,' Berlin, Springer
  19. Vetrano, J. S., Lavender, C. A., Hamilton, C. H., Smith, M. T. and Bruemmer, S. M., 1994, 'Superplastic Behavior in a Commercial 5083 Aluminum Alloy,' Scripta Metall., Vol. 30, pp. 565-570 https://doi.org/10.1016/0956-716X(94)90430-8