DOI QR코드

DOI QR Code

Prediction on load carrying capacities of multi-storey door-type modular steel scaffolds

  • Yu, W.K. (Department of Civil and Structural Engineering, The Hong Kong Polytechnic University) ;
  • Chung, K.F. (Department of Civil and Structural Engineering, The Hong Kong Polytechnic University)
  • 투고 : 2004.09.24
  • 심사 : 2004.11.22
  • 발행 : 2004.12.25

초록

Modular steel scaffolds are commonly used as supporting scaffolds in building construction, and traditionally, the load carrying capacities of these scaffolds are obtained from limited full-scale tests with little rational design. Structural failure of these scaffolds occurs from time to time due to inadequate design, poor installation and over-loads on sites. In general, multi-storey modular steel scaffolds are very slender structures which exhibit significant non-linear behaviour. Hence, secondary moments due to both $P-{\delta}$ and $P-{\Delta}$ effects should be properly accounted for in the non-linear analyses. Moreover, while the structural behaviour of these scaffolds is known to be very sensitive to the types and the magnitudes of restraints provided from attached members and supports, yet it is always difficult to quantify these restraints in either test or practical conditions. The problem is further complicated due to the presence of initial geometrical imperfections in the scaffolds, including both member out-of-straightness and storey out-of-plumbness, and hence, initial geometrical imperfections should be carefully incorporated. This paper presents an extensive numerical study on three different approaches in analyzing and designing multi-storey modular steel scaffolds, namely, a) Eigenmode Imperfection Approach, b) Notional Load Approach, and c) Critical Load Approach. It should be noted that the three approaches adopt different ways to allow for the non-linear behaviour of the scaffolds in the presence of initial geometrical imperfections. Moreover, their suitability and accuracy in predicting the structural behaviour of modular steel scaffolds are discussed and compared thoroughly. The study aims to develop a simplified and yet reliable design approach for safe prediction on the load carrying capacities of multi-storey modular steel scaffolds, so that engineers can ensure safe and effective use of these scaffolds in building construction.

키워드

참고문헌

  1. British Standards Institution. BS5950: Structural use of steelwork in building. Part 1: Code of practice for design - Rolled and welded sections, 2000.
  2. British Standards Institution. BS5975: Code of practice for falsework, 1996.
  3. Chan, S.L. and Zhou, Z.H. (1998),"On the development of a robust element for second-order Non-linear integrated design and analysis (NIDA)", J. of Constructional Steel Research, 47(I-II), 169-190. https://doi.org/10.1016/S0143-974X(98)80107-7
  4. Chung, K.F. and Yu, W.K. (2003),"Experimental and theoretical investigations on modular steel scaffolds", Proc. of Technical Seminar on Metal Scaffolding (Falsework) - Design, Construction & Safety, the Hong Kong Institute of Steel Construction, Hong Kong, 13-23.
  5. European Standard. Eurocode 3: Design of steel structures. Part 1-1: General rules and rules of buildings, 1993 & 2003.
  6. Godley, M.H.R. and Beale, R.G. (1997),"Sway stiffness of scaffold structures", The Structural Engineer, 75(1), 4-12.
  7. Godley, M.H.R. and Beale, R.G. (2001),"Analysis of large proprietary access scaffold structures", Proc. of the Institution of Civil Engineers, Structures and Buildings, 146, 31-39. https://doi.org/10.1680/stbu.2001.146.1.31
  8. Gylltoft, K. and Mroz, K. (1995),"Load carrying capacity of scaffolds", Struct. Eng. Int., 1, 37-42.
  9. Holmes, M. and Hindson, D. (1979),"Structural behaviour of load bearing falsework", Proc. of Institution of Civil Engineers, 67, 721-741. https://doi.org/10.1680/iicep.1979.2861
  10. Huang, Y.L., Chen, H.J., Rosowsky, D.V. and Kao, Y.G. (2000a),"Load-carrying capacities and failure modes of scaffold-shoring systems, Part I: Modeling and experiments", Struct. Eng. Mech., 10(1), 53-66. https://doi.org/10.12989/sem.2000.10.1.053
  11. Huang, Y.L., Kao, Y.G. and Rosowsky, D.V. (2000b),"Load-carrying capacities and failure modes of scaffoldshoring systems, Part II: An analytical model and its closed-form solution", Struct. Eng. Mech., 10(1), 67-79. https://doi.org/10.12989/sem.2000.10.1.067
  12. Liew, J.Y.R., White, D.W. and Chen, W.F. (1994),"Notional-load plastic-hinge method for frame design", J. of Struct. Eng., 120(5), 1434-1454. https://doi.org/10.1061/(ASCE)0733-9445(1994)120:5(1434)
  13. Lightfoot, E. and Oliveto, G. (1977),"The collapse strength of tubular steel scaffold assemblies", Proc. of Institution of Civil Engineers, 63, 311-329. https://doi.org/10.1680/iicep.1977.3181
  14. Milokovic, B., Beale, R.G. and Godley, M.H.R. (2002),"Determination of the factors of safety of standard scaffolds structures", Proc. of the Third Int. Conf. on Advances in Steel Structures, 1, 303-310.
  15. Peng, J.L. (1994),"Analysis models and design guidelines for high-clearance scaffold systems", Ph.D. Dissertation, School of Civil Engineering, Purdue University.
  16. Peng, J.L., Pan, A.D.E., Chen, W.F., Yen, T. and Chan, S.L. (1997),"Structural modeling and analysis of modular falsework systems", J. of Struct. Eng., 123(9), 1245-1251. https://doi.org/10.1061/(ASCE)0733-9445(1997)123:9(1245)
  17. Peng, J.L., Pan, A.D., Rosowsky, D.V., Chen, W.F., Yen, T. and Chan, S.L. (1996),"High clearance scaffold systems during construction I. Structural modeling and modes of failure", Eng. Struct., 18(3), 247-257. https://doi.org/10.1016/0141-0296(95)00144-1
  18. Weesner, L.B. and Jones, H.L. (2001),"Experimental and analytical capacity of frame scaffolding", Eng. Struct., 23(6), 592-599. https://doi.org/10.1016/S0141-0296(00)00087-0
  19. Yu, W.K. (2004a),"Structural behaviour of tubular skeletal framework", Ph.D Thesis, the Hong Kong Polytechnic University.
  20. Yu, W.K. (2004b),"An Investigation into structural behaviour of modular steel scaffolds", J. of Steel and Composite Structures, 4(3), 211-226. https://doi.org/10.12989/scs.2004.4.3.211
  21. Yu, W.K., Chung, K.F. and Chan, S.L. (2002),"Structural stability of modular steel scaffolding systems", Proc. of the Second Int. Conf. on Stability and Dynamic, Singapore, 418-423.
  22. Yu, W.K., Chung, K.F. and Chan, S.L. (2004),"Structural instability of multi-storey door-type modular steel scaffolds", Eng. Struct., 26(7), 867-881. https://doi.org/10.1016/j.engstruct.2004.02.006

피인용 문헌

  1. Structural modelling of support scaffold systems vol.67, pp.5, 2011, https://doi.org/10.1016/j.jcsr.2010.12.007
  2. EXPERIMENTAL STUDY OF LOAD CAPACITIES OF TUBULAR STEEL ADJUSTABLE SHORES USED IN CONSTRUCTION vol.13, pp.04, 2013, https://doi.org/10.1142/S0219455412500630
  3. Investigation of geometric imperfections and joint stiffness of support scaffold systems vol.67, pp.4, 2011, https://doi.org/10.1016/j.jcsr.2010.12.004
  4. Effects of geometrical shape and incremental loads on scaffold systems vol.63, pp.4, 2007, https://doi.org/10.1016/j.jcsr.2006.07.006
  5. Experimental Study on Load-Bearing Capacities of Frame-Type Scaffolds Used in Precast Construction vol.20, pp.2, 2004, https://doi.org/10.1007/s13296-019-00292-6
  6. Experimental Investigations on Ultimate Behavior of Fabricated Mobile Scaffolds vol.11, pp.6, 2021, https://doi.org/10.3390/met11060851