DOI QR코드

DOI QR Code

Experimental investigation on steel-concrete bond in lightweight and normal weight concrete

  • Chen, How-Ji (Department of Civil Engineering, National Chung-Hsing University) ;
  • Huang, Chung-Ho (Department of Civil Engineering, National Chung-Hsing University) ;
  • Kao, Zhang-Yu (Department of Civil Engineering, National Chung-Hsing University)
  • 투고 : 2002.06.18
  • 심사 : 2003.11.03
  • 발행 : 2004.02.25

초록

The bonding behaviors of Lightweight Aggregate Concrete (LWAC) and normal weight concrete were investigated experimentally. Pull-out tests were carried out to measure the bond strengths of three groups of specimens with compressive strength levels of 60, 40, and 20 MPa, respectively. Test results showed that the difference in the bond failure pattern between LWAC and normal weight concrete was significant as the concrete compressive strength became lower than 40 MPa. The corresponding bond strengths of LWAC were lower than that for normal weight concrete. As the compressive strength of concrete became relatively high (> 40 MPa), a bond failure pattern in normal weight concrete occurred that was similar to that in LWAC. The bond strength of LWAC is higher than that for normal weight concrete because it possesses higher mortar strength. Stirrup use leads to an increase of approximately 20% in nominal bond strength for both types of concrete at any strength level.

키워드

참고문헌

  1. Chen, H.J., Yen, T., Lia, T.P. and Huang, Y.L. (1999), "Determination of the dividing strength and its relation to the concrete strength in lightweight aggregate concrete", Cement and Concrete Composites, 21, 29-37. https://doi.org/10.1016/S0958-9465(98)00035-3
  2. Chinn, J., Feruson, P.M. and Thompson, J.N. (1955), "Lapped splices in R.C. beam", ACI Journal, 52(2), 201- 214.
  3. Eligehausen, R., Popov, E.P. and Bertero, V.V. (1982), "Local bond stress-slip relationships of deformed bars under generalized excitations", Proc. of the Seventh European Conf. on Earthquake Engineering, Athens, 69-80.
  4. Kenneth Leet (1991), Reinforced Concrete Design, Second Edition, McGraw-Hill, Inc., 231-242
  5. Lutz, L.A. and Gergely, P. (1976), "Mechanics of bond and slip of deformed bars in concrete", ACI Journal, Proceeding, 64(11), 711-721.
  6. Mathey, R.G. and Watstein, D. (1961), "Investigation of bond in beam and pull-out specimens with high-yield - strength deformed bars", ACI Journal, 57(9), 1071-1090.
  7. Mor, A. (1992), "Steel-concrete bond in high-strength lightweight concrete", ACI Materials Journal, 76-82.
  8. Robins, P.J. and Austin, S.A. (1986), "Bond of lightweight aggregate concrete incorporating condensed silica fume", Fly Ash, Silica Fume, Slag and Natural Pozzolans, ACI, Detroit, 941-958.
  9. Wilson, H.S. and Malhotra, M. (1988), "Development of high strength lightweight concrete for structural application", Int. J. Cement Composites and Lightweight Concrete, 79-90.

피인용 문헌

  1. Bond properties of lightweight concrete – A review vol.112, 2016, https://doi.org/10.1016/j.conbuildmat.2016.02.125
  2. Steel–concrete bond in lightweight fiber reinforced concrete under monotonic and cyclic actions vol.27, pp.6, 2005, https://doi.org/10.1016/j.engstruct.2005.01.010
  3. Dynamic Properties of Lightweight Concrete Beams Made by Sedimentary Lightweight Aggregate vol.22, pp.6, 2010, https://doi.org/10.1061/(ASCE)MT.1943-5533.0000061
  4. Flexural and Shear Resistance of Steel Fiber–Reinforced Lightweight Concrete Beams vol.140, pp.4, 2014, https://doi.org/10.1061/(ASCE)ST.1943-541X.0000887
  5. Experimental Investigation on the Properties of Lightweight Concrete Containing Waste Oil Palm Shell Aggregate vol.125, 2015, https://doi.org/10.1016/j.proeng.2015.11.065
  6. Experimental Research on Bond Behaviors between Shale Ceramsite Lightweight Aggregate Concrete and Bars through Pullout Tests vol.27, pp.9, 2015, https://doi.org/10.1061/(ASCE)MT.1943-5533.0001192
  7. Bond of steel reinforcement with microwave cured concrete repair mortars vol.50, pp.6, 2017, https://doi.org/10.1617/s11527-017-1115-6
  8. Shear strength of steel fiber reinforced concrete beams with stirrups vol.24, pp.1, 2006, https://doi.org/10.12989/sem.2006.24.1.107
  9. Self-Consolidating Concretes Made with Cold-Bonded Fly Ash Lightweight Aggregates vol.114, pp.3, 2017, https://doi.org/10.14359/51689606
  10. A Review on Bond and Anchorage of Confined High-strength Concrete vol.11, 2017, https://doi.org/10.1016/j.istruc.2017.04.004
  11. Bond strength evaluation of palm oil fuel ash-based geopolymer normal weight and lightweight concretes with steel reinforcement vol.32, pp.1, 2018, https://doi.org/10.1080/01694243.2017.1336195
  12. Time-Dependent Properties of Lightweight Concrete Using Sedimentary Lightweight Aggregate vol.168-170, pp.1662-8985, 2010, https://doi.org/10.4028/www.scientific.net/AMR.168-170.2235
  13. A Study of Interfacial Transition Zone in Lightweight Aggregate Concrete vol.194-196, pp.1662-8985, 2011, https://doi.org/10.4028/www.scientific.net/AMR.194-196.935
  14. Stability and Bond Properties of Latex-Modified Semi-Lightweight Flowable Concrete vol.115, pp.4, 2018, https://doi.org/10.14359/51702010
  15. Bond to reinforcement of polymeric lightweight flowable concrete for structural applications pp.1568-5616, 2019, https://doi.org/10.1080/01694243.2018.1547473
  16. Influence of high-cycle fatigue on the tension stiffening behavior of flexural reinforced lightweight aggregate concrete beams vol.40, pp.6, 2011, https://doi.org/10.12989/sem.2011.40.6.847