Development of Machine Vision System and Dimensional Analysis of the Automobile Front-Chassis-Module

  • Lee, Dong-Mok (Graduate school of Mechanical Engineering, Kyungpook National University) ;
  • Yang, Seung-Han (School of Mechanical Engineering, Kyungpook National University) ;
  • Lee, Sang-Ryong (School of Mechanical Engineering, Kyungpook National University) ;
  • Lee, Young-Moon (School of Mechanical Engineering, Kyungpook National University)
  • 발행 : 2004.12.01

초록

In the present research work, an automated machine vision system and a new algorithm to interpret the inspection data has been developed. In the past, the control of tolerance of front-chassis-module was done manually. In the present work a machine vision system and required algorithm was developed to carryout dimensional evaluation automatically. The present system is used to verify whether the automobile front-chassis-module is within the tolerance limit or not. The directional ability parameters related with front-chassis-module such as camber, caster, toe and king-pin angle are also determined using the present algorithm. The above mentioned parameters are evaluated by the pose of interlinks in the assembly of an automobile front-chassis-module. The location of ball-joint center is important factor to determine these parameters. A method to determine the location of ball-joint center using geometric features is also suggested in this paper. In the present work a 3-D best fitting method is used for determining the relationship between nominal design coordinate system and the corresponding feature coordinate system.

키워드

참고문헌

  1. Arun, K. S., Huang, T. S. and Blostein, S. D., 1987, 'Least-Squares Fitting of two 3-D Point Sets,' IEEE Trans. Pattern Anal. Machine Intell., Vol. PAMI-9, pp. 698-700 https://doi.org/10.1109/TPAMI.1987.4767965
  2. Eggert, D. W., Lorusso, A. and Fisher, R. B., 1997, 'Estimating 3-D Rigid Body Transformations : A Comparison of Four Major Algorithms,' Vol. 9, No. 5-6, pp. 272-290 https://doi.org/10.1007/s001380050048
  3. Horn, B. K. P., 1987, 'Closed-Form Solution of Absolute Orientation using Orthonormal Matrices,' J. Opt. Soc. Am. Ser. A, Vol. 5, pp. 1127-1135
  4. Kondo, M., Tachiki, S. and Ishida, M., 1995, 'Automatic Measuring System for Body Fit on the Automobile Assembly Line,' Robotics and Automation, Proceedings, IEEE International Conference, Vol. 1, pp. 538-543 https://doi.org/10.1109/ROBOT.1995.525339
  5. Lee, S. H., Kim, I. S. and Katupitiya, J., 2002, 'A Fuzzy-Logic Controller for an Electrically Driven Steering System for a Motorcar,' KSME International Journal, Vol. 16, pp. 1039-1052
  6. Ozdalyan, B., Blundell, M. V., and Phillips, B., 1998, 'Comparison of Suspension Rig Measurements with Computer Simulation,' International Conference on SIMULATION, No. 457, pp. 133-139
  7. Samuel, G. L. and Yang, S. H., 2003, 'Determination and Mapping of Measurement and Design Coordinate Systems using Computational Geometric Techniques,' International Journal of Advanced Manufacturing Technology, Accepted https://doi.org/10.1007/s00170-003-2052-9
  8. Sheng, W., Xi, N., Song, M., Chen, Y., and Rankin III, J. S., 2000, 'Automated CAD Guided Automobile part Dimensional Inspection,' Robotics and Automation, Proceedings. ICRA 00. IEEE International Conference, Vol. 2,pp. 1157-1162 https://doi.org/10.1109/ROBOT.2000.844755
  9. Umeyama, S., 1991, 'Least-Squares Estimation of Transformation Parameters between Two Point Patterns,' IEEE Trans. Pattern Anal. Machine Intell., Vol. 13, pp. 376-380 https://doi.org/10.1109/34.88573
  10. Yau, H. T. and Menq, C. H., 1996, 'A Unified Least-Squares Approach to the Evaluation of Geometric Errors using Discrete Measurement Data,' International Journal of Machine Tools and Manufacture, Vol. 36, No. 11, pp. 1269-1290 https://doi.org/10.1016/0890-6955(95)00075-5
  11. Zetterstrom, S., 2002, 'Electromechanical Steering, Suspension, Drive and Brake Modules,' Proceedings of IEEE 56th Vehicular Technology Conference-2002 (VTC-2002, Fall), Vol. 3, pp. 1856-1863 https://doi.org/10.1109/VETECF.2002.1040538