대한기계학회논문집A (Transactions of the Korean Society of Mechanical Engineers A)

  • 제28권5호
  • /
  • Pages.554-562
  • /
  • 2004
  • /
  • 1226-4873(pISSN)
  • /
  • 2288-5226(eISSN)
대한기계학회 (The Korean Society of Mechanical Engineers)
권호 표지
DOI QR코드

DOI QR Code

Mn-Mo-Ni 저합금강의 SP-곡선과 인장물성과의 실험적 관계

Empirical Relationship Between SP-curves and Tensile Properties in Mn-Mo-Ni Low Alloy Steels

  • 이재봉 (충북대학교 안정공학과) ;
  • 김민철 (한국원자력연구소 원자력재료기술개발부) ;
  • 박재학 (충북대학교 안전공학과) ;
  • 이봉상 (한국원자력연구소 원자력재료기술개발부)
  • 발행 : 2004.05.01
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

An empirical relationship between parameters from SP curves and tensile properties has been systematically investigated by experimental tests and FEM simulations. A series of SP and tensile tests were performed. SP tests were also simulated by FE analysis with various tensile properties. It was found that the yield loads(Py) and the maximum loads( $P_{MAX}$) in SP curves were linearly related with the yield strength($\sigma$$_{o}$) and the tensile strength($\sigma$$_{UTS}$), respectively. The yield loads defined from the intersection point of two lines tangent to the elastic bending region and plastic bending region showed better relation to the yield strength than those from offset line. The maximum loads in SP curves showing plastic instability region was linearly related with the tensile strengths. The slope of SP curves in simulation results had a close correlation with the hardening coefficient and hardening strength as well.l.l.l.

키워드

참고문헌

  1. Ghosh, A.K. and Hecker, S.S., 1975, 'Failure in Thin Sheets Stretched over Rigid Puncher,' Metallurgical Transactions, Vol. 6A, pp.1065-1074 https://doi.org/10.1007/BF02661361
  2. Lucas, G.E., Okada, A., and Kiritani, M., 1986, 'Parametric Analysis of the Disc Bend Test,' Journal of Nuclear Materials, Vol. 141-143, pp.532-535 https://doi.org/10.1016/S0022-3115(86)80096-4
  3. Kameda, J. and Mao, X., 1992, 'Small-Punch and TEM-Disc Testing Techniques and Their Application to Characterization of Radiation Damage,' Journal of Materials Science, Vol. 27, pp.983-989 https://doi.org/10.1007/BF01197651
  4. Kim, J.K., Lee, J.K.,Yoon, K.B., and Chung, S.H., 1991, 'Study on Evaluation by Small Punch Test for Material Degradation of Steam Tubes of Fossile Electric Power Plant,' Transaction of KSME(A), Vol. 15, No. 5, pp.1665-1673
  5. Fleury, E. and Ha, J.S., 1998, 'Small Punch Tests to Estimate The Mechanical Properties of Steels for Steam Power plant: I. Mechanical Strength,' Journal of Pressure Vessels and Piping, Vol. 75, pp.699-706 https://doi.org/10.1016/S0308-0161(98)00074-X
  6. Fleury, E. and Ha, J.S., 1998, 'Small Punch Tests to Estimate The Mechanical Properties of Steels for steam Power Plant:II. Fracture Toughness,' Journal of Pressure Vessels and Piping, Vol. 75, pp.707-713 https://doi.org/10.1016/S0308-0161(98)00075-1
  7. Mao, X. and Takahashi, H., 1987, 'Development of A Further-Miniatured Specimen of 3mm Diameter for TEM Disk(${\Phi}3mm$) Small Punch Tests,' Journal of Nuclear Materials, Vol. 150, pp.42-52 https://doi.org/10.1016/0022-3115(87)90092-4
  8. Mao, X., Shoji, T., and Takahashi, H., 1987, 'Characterization of Fracture Behavior in Small Punch Test by combined Recrystallization-Etch Method and Rigid Plastic Analysis,' Journal of Testing and Evaluation, Vol. 15, pp.30-37 https://doi.org/10.1520/JTE11549J
  9. Lee, W.K., Metzger, D.R., Donner, A., and Lepik, O., 1998, 'The Use of a Small Punch Test Procedure to Determine Mechanical Properties,' Small Specimen Test Techniques, ASTM STP 1329, W. R. Corwin, S. T. Rosaski, and E. Van Walle Eds., ASTM, pp.539-556
  10. Foulds, J.R., Woytowitz, P.J., Parnell, T.K., and Jewett, C.W., 1995, 'Fracture Toughness by Small Punch Testing,' Journal of Testing and Evaluation, Vol. 23, pp.3-10 https://doi.org/10.1520/JTE10392J
  11. Yu, H.S., Nho, S.H., Chung, S.H., and Ong, J.W., 1995, 'A Study on the Small Punch Test For Fracture Strength Evaluation of CANDU Pressure Tube Embrittled by Hydrogen,' Transactions of Korea Society Nondestructive Testing, Vol. 15, No. 4, pp.510-521
  12. Okada, A., Hamilton, M.L., and Garner, F.A., 1991, 'Microbulge Testing Applied to Neutron Irradiated Materials,' Journal of Nuclear Materials, Vol. 179/181, pp.445-448 https://doi.org/10.1016/0022-3115(91)90120-V
  13. Xu, Y., Ning, G., Zhang, C., Yu, Q., and Xu, Y., 2000, 'Application of The Miniature Specimen Technique to Material Irradiation Tests and Surveillance for Reactor Component,' Journal of Pressure Vessels and Piping, Vol. 77, pp.715-721 https://doi.org/10.1016/S0308-0161(00)00066-1