대한기계학회논문집A (Transactions of the Korean Society of Mechanical Engineers A)

  • 제27권8호
  • /
  • Pages.1398-1408
  • /
  • 2003
  • /
  • 1226-4873(pISSN)
  • /
  • 2288-5226(eISSN)
대한기계학회 (The Korean Society of Mechanical Engineers)
권호 표지
DOI QR코드

DOI QR Code

냉간가공된 316L 스테인리스 강의 인장 및 저주기 피로 물성치에 미치는 동적변형시효의 영향

The Influence of Dynamic Strain Aging on Tensile and LCF Properties of Prior Cold Worked 316L Stainless Steel

  • 홍성구 (한국과학기술원 기계공학과) ;
  • 이순복 (한국과학기술원 기계공학과)
  • 발행 : 2003.08.01
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

Tensile and LCF(low cycle fatigue) tests were carried out in air at wide temperature range 20$^{\circ}C$-750$^{\circ}C$ and strain rates of 1${\times}$10$\^$-4//s-1${\times}$10$\^$-2/ to ascertain the influence of strain rate on tensile and LCF properties of prior cold worked 316L stainless steel, especially focused on the DSA(dynamic strain aging) regime. Dynamic strain aging induced the change of tensile properties such as strength and ductility in the temperature region 250$^{\circ}C$-600$^{\circ}C$ and this temperature region well coincided with the negative strain rate sensitivity regime. Cyclic stress response at all test conditions was characterized by the initial hardening during a few cycles, followed by gradual softening until final failure. Temperature and strain rate dependence on cyclic softening behavior appears to result from the change of the cyclic plastic deformation mechanism and DSA effect. The DSA regimes between tensile and LCF loading conditions in terms of the negative strain rate sensitivity were well consistent with each other. The drastic reduction in fatigue resistance at elevated temperature was observed, and it was attributed to the effects of oxidation, creep and dynamic strain aging or interactions among them. Especially, in the DSA regime, dynamic strain aging accelerated the reduction of fatigue resistance by enhancing crack initiation and propagation.

키워드

참고문헌

  1. Kanazawa K., Yamaguchi K., Nishijima S., 1988, 'Mapping of low cycle fatigue mechanisms at elevated temperatures for an austenitic stainless steel,' ASTM STP 942, pp. 519-530
  2. Bressers, J., 1987, 'In High Temperature Alloys, Their Exploitable Potential,' Elsevier Applied Science, Amsterdam, pp. 385-410
  3. Valsan M., Sastry D. H., Bhanu Sankara Rao K., Mannan S. L., 1994, 'Effect of strain rate on the high-temperature low-cycle fatigue properties of a nimonic PE-16 superalloy,' Metall. Trans., 25A, pp. 159-171 https://doi.org/10.1007/BF02646684
  4. Srinivasan, V. S., Sandhya R., Bhanu Sankara Rao K., Mannan S. L., Raghavan K. S., 1991, 'Effect of temperature on the low cycle fatigue behavior of nitrogen alloyed type 316L stainless steel,' Int. J. Fat., 13(6), pp. 471-478 https://doi.org/10.1016/0142-1123(91)90482-E
  5. Srinivasan, V. S., Valsan, M., Sandhya, R., Bhanu Sankara Rao, K., Mannan, S. L. and Sastry, D. H., 1999, 'High temperature time-dependent low cycle fatigue behavior of a type 316(N) stainless steel,' Int. J. Fat., 21, pp. 11-21 https://doi.org/10.1016/S0142-1123(98)00052-8
  6. Rodriguez, P., 1988, 'Encyclopedia of materials science and engineering,' Suppl. Vol. 1, Pergamon press, N. Y., pp. 504-508
  7. Mannan, S. L., Samuel, K. G. and Rodriguez, P., 1983, Trans. Ind. Inst. Metals, 36, pp. 313
  8. Kim, D. J., 1988, Ph. D. thesis, Dept. Mater. Sci., KAIST
  9. Challenger, K. D., Miller, A. K. and Brinkman, C. R., 1981, 'An explanation for the effects of hold periods on the elevated temperatur fatigue behavior of 2 1/4 Cr-1Mo steel,' J. Eng. Mat. Tech., 103, pp. 7-14 https://doi.org/10.1115/1.3224979
  10. Abdel-Raouf, H., Plumtree, A. and Topper, T. H., 1973, 'Effects of temperature and deformation rate on cyclic strength and fracture of low carbon steel,' ASTM STP 519, pp. 28-57
  11. Hong, S. G. and Lee, S. B., 2002, 'Development of a new LCF life prediction model of 316L stainless steel at elevated temperature,' KSME Trans. A, 26(3), pp. 521-527 https://doi.org/10.3795/KSME-A.2002.26.3.521
  12. van den Beukel, A., 1980, 'On the mechanism of serrated yielding and dynamic strain aging,' Acta Metall., 28, pp. 965-969 https://doi.org/10.1016/0001-6160(80)90114-5
  13. Bhanu Sankara Rao K., Valsan M., Sandhya R., Mannan S. L., Rodriguez P., 1993, 'An Assessment of Cold Work Effects on Strain-Controlled Low Cycle Fatigue Behavior of Type 304 Stainless Steel,' Metall. Trans., 24A, pp. 913-924 https://doi.org/10.1007/BF02656512
  14. Plumbridge W. J., Dalski M. E., Castle P. J., 1980, 'High strain fatigue of a type 316 stainless steel,' Fract. Eng. Mater. Struct., 3, pp. 177-188 https://doi.org/10.1111/j.1460-2695.1980.tb01112.x
  15. Ganesh Sundara Raman, S. and Padmanabhan, K.A., 1996, 'Effect of Prior Cold Work on the Room-Temperature Low Cycle Fatigue Behavior of AISI 304LN Stainless Steel,' Int. J. Fatigue, 18(2), pp. 71-79 https://doi.org/10.1016/0142-1123(95)00078-X
  16. Sherman, A. M., 1975, 'Fatigue properties of high strength-low alloy steels,' Metall. Trans., 6A, pp. 1035-1040 https://doi.org/10.1007/BF02661357
  17. Morrow, J. D., 1964, ASTM STP 378, pp. 45-84
  18. Hong, S. G., Samson Yoon and Lee, S. B., 2003, 'The influence of temperature on low cycle fatigue behavior of prior cold worked 316L stainless steel (I) - monotonic and cyclic behavior,' KSME Trans. A, accepted
  19. Driver J. H., Gorier C., Belrami C., Vidan P., Amzallag C., 1988, 'Influence of temperature and environment on the fatigue mechanisms of single-crystal and polycrystal 316L,' ASTM STP 942, pp. 438-455

피인용 문헌

  1. Effects of Alloying Elements on Tensile Properties at Elevated Temperature and on Hardness of Heat-Affected-Zone in High-Purity Fe-18Cr-16Ni Alloys vol.70, pp.8, 2006, https://doi.org/10.2320/jinstmet.70.694