DOI QR코드

DOI QR Code

금속 벨로우즈 Diaphragm용 CAD 프로그램 개발

A Development of CAD Program for Metal Bellows Diaphragm

  • 조해용 (충북대학교 기계공학부) ;
  • 남기정 (충북대학교 대학원) ;
  • 오병기 (충북대학교 대학원) ;
  • 김영훈 (충북대학교 대학원) ;
  • 이제훈 (한국기계연구원 레이저 기술그룹) ;
  • 서정 (한국기계연구원 레이저 기술그룹)
  • 발행 : 2003.03.01

초록

A CAD program for metal bellows diaphragm was developed in this study. This program was written in AutoLISP on the AutoCAD system with a personal computer. Basic design concept used in this program is composition of a convolution that is tangent to two lines and 5 circles from given design parameters(initial radius, inner and outer diameter, thickness, pitch, etc.). The effects of altering some design parameters on stress distribution and fatigue life of bellows were estimated using commercial FEM code, NISAII. As a result, the metal bellows diaphragm was successfully designed by the CAD program. It is used to model a bellows geometry in pre-processor of FEM code. The FEM result shows that stress is dependent on straight line length, bellows diameter with same span, and fatigue life is also affected by design parameters.

키워드

참고문헌

  1. Osamu HIRATA, Akira NAKAJIMA, Ken OKADA, Shinji SASAKI and Yoshihiro OGAWA, 1995, 'Fatigue Life of Welded Bellows (Effect of Configuration of Corrugated Plate),' Journal of the Japan Society for Engineering, Vol. 61, No. 587, pp. 3143-3149
  2. Osamu HlRATA, Akira NAKAJIMA Ken OKADA, Shinji SASAKI and Yoshihiro OGAWA 1995. 'Fatigue Life of Welded Bellows (Effect of Test Speed),' Journal of the Japan Society for Engineering. Vol. 61. No. 589, pp. 3755-3761
  3. Cho. H. I., Kim. W. D. and Woo, C. S., 1991. 'Analysis of Welded Metal Bellows.' KIMM. Vol. 21. pp. 51-61
  4. Troitsky, M. S., 1976, 'Stiffened Plates Bending. Stability and Vibrations,' Elsevier Scientific Publishing Company. pp. 62-90
  5. Ugural, A. C., 1981, 'Stresses in plates and shells,' McGraw-Hill, pp. 1-25
  6. Hosford, W. F., 1983, 'Metal Forming Mechanics and Metallurgy.' Prentice-Hall, pp. 294-310
  7. Choi, J. C., Kim., B. M., Kim, C. and Kim, J. H., 1996, 'An Automated Process Planning System for Blanking of Stator and Rotor Parts and Irregularly-Shaped Sheet Metal Products.' KSPE. Vol. 13, No.9. pp. 46-53
  8. 'Welded Metal Bellows,' Product Bulletin.. Morpho Corp.
  9. 'NISAII/DISPLAYIII user's manual' 1996. Engineering Mechanics Research Corporation
  10. Bannantine. Jule A.. 1990. 'Fundamentals of Metal Fatigue Analysis.' Prentice-Hall. pp. 1-70

피인용 문헌

  1. A Study on Programming Development Forming Design Automated of CAM for Coil Spring Forming Tool vol.32, pp.5, 2008, https://doi.org/10.5916/jkosme.2008.32.5.753