Three dimensional finite element method for stress distribution on the length and diameter of orthodontic miniscrew and cortical bone thickness

교정용 미니스크류 식립 시 스크류의 길이, 직경 및 피질골 두께에 따른 응력 분포에 관한 3차원 유한요소법적 연구

  • Lim, Jong-Won (Division of Orthodontics, Department of Dentistry, College of Medicine, Inha University) ;
  • Kim, Wang-Sik (Division of Orthodontics, Department of Dentistry, College of Medicine, Inha University) ;
  • Kim, Il-Kyu (Division of Orthodontics, Department of Dentistry, College of Medicine, Inha University) ;
  • Son, Choong-Yul (Division of Orthodontics, Department of Dentistry, College of Medicine, Inha University) ;
  • Byun, Hyo-In (Division of Orthodontics, Department of Dentistry, College of Medicine, Inha University)
  • 임종원 (인하대학교 의과대학 치과학교실) ;
  • 김왕식 (인하대학교 의과대학 치과학교실) ;
  • 김일규 (인하대학교 의과대학 치과학교실) ;
  • 손충렬 (인하대학교 의과대학 치과학교실) ;
  • 변효인 (인하대학교 의과대학 치과학교실)
  • Published : 2003.02.01

Abstract

The purpose of the present study is to evaluate the stress distribution on the length and diameter of the miniscrew and cortical bone width. Three dimensional finite element models were made of diameter 1.2mm, 1.6mm, 2.0mm and length 6.0mm, 8.0mm, 10.0mm, 12.0mm and cortical bone width 1.0mm. Also, another three dimensional finite element models were made of diameter 1.2mm, 1.6mm, 2.0mm and length 8.0mm and cortical bone width 1.0mm, 1.5mm, 2.0mm, 2.5mm. Two-hundred grams horizontal force were applied on the center of the miniscrew head and at that stress distribution and its magnitude had been analyzed by ANSYS, which is three dimensional finite element analysis program. The obtained results were as follows : 1. The comparison of the maximum von-Mises stress in the miniscrew showed that as the diameter increases from 1.2mm to 2.0mm stress has been decreased, while on the same diameter stress was not changed regardless of the length change. 2. The comparison of the maximum von-Mises stress in the cortical and cancellous bone showed that as the diameter increases from 1.2mm to 2.0mm stress has been decreased, while on the same diameter stress was not changed regardless of the length change. 3. In the analysis of the stress distribution in the cortical and cancellous bone, the most of the stress had been absorbed in the cortical bone, and did not transmitted much to the cancellous bone. 4. In the analysis of the maximum von-Mises stress according to the cortical bone width, the same diameter of the miniscrew showed a constant stress value regardless of the cortical bone width change. The above results suggest that the maintenance of the miniscrew is more reliable on diameter than length of the miniscrew.

본 연구는 교정치료 시 고정원 보강을 위해 사용되는 교정용 미니스크류의 길이, 직경 및 피질골 두께에 따른 응력 분포 양상을 알아보기 위하여 시행되었다. 미니스크류의 길이와 직경 변화에 따른 응력 분포 양상을 관찰하기 위하여 식립되는 피질골의 두께를 1.0mm로 고정하고 미니스크류의 길이를 6.0mm, 8.0mm, 10.0mm, 12.0mm로, 직경을 1.2mm, 1.6mm, 2.0mm인 3차원 유한요소 모델을 제작하였다. 또한, 피질골의 두께 변화에 따른 응력 분포 양상을 관찰하기 위하여 미니 스크류의 길이를 8.0mm로 고정하고 직경은 1.2mm, 1.6mm, 2.0mm로, 피 질골의 두께는 1.0mm, 1.5mm, 2.0mm, 2.5mm인 3차원 유한요소 모델을 제작하였다. 각각의 유한요소 모델의 미니스크류 head중심에 200gm의 수평력을 가하여 응력 분포 양상과 크기를 3차원 유한요소 해석 프로그램인 ANSYS를 이용하여 비교한 결과 다음과 같은 결론을 얻었다. 1. 미니스크류 내부에서 나타나는 최대 응력값을 비교한 결과, 미니스크류의 직경이 1.2mm에서 2.0mm로 증가할수록 응력이 감소하였으며 같은 직경에서는 길이 증가에 상관없이 일정한 값을 유지하였다. 2. 피질골 및 해면골에 작용되는 최대 응력값을 비교한 결과, 미니스크류의 직경이 1.2mm에서 2.0mm로 증가할수록 응력이 감소하였으며 같은 직경에서는 길이 증가에 상관없이 일정한 값을 유지하였다. 3. 피질골 및 해면골에 작용되는 응력 분포를 관찰한 결과, 대부분의 응력이 피질골에서 흡수되었으며 ,해면골에 전달되는 응력값은 미미하였다. 4. 피질골 두께에 따른 최대 응력값을 비교한 결과, 같은 미니스크류의 직경에서는 피질골의 두께 증가에 상관없이 일정한 값을 유지하였다. 이상의 결과는 교정용 미니스크류의 유지에 길이보다는 직경이 더 크게 관여하는 것으로 나타나 미니스크류의 식립시 이에 대한 고려가 필요함을 시사하였다.

Keywords

References

  1. Wehrbein H, Merz BR, Diedrich P, Glatzmaier J. The use of palatal implants for orthodontic anchorage. Clin Oral Impl Res 1996 : 7 : 410-6
  2. Melsen B, Petersen JK, Costa A. Zygoma ligatures : An alternative form of maxillary anchorage. J Clin Ortho 1998 : 32 : 154-8
  3. Umemori M, Sugawara J, Mitani H, Nagasaka H, Kawamura H. Skeletal anchorage system for open-bite correction. Am J Orthod Dentofac Orthop 1999 : 115 : 166-74
  4. Kanomi R. Mini-implant for orthodontic anchorage. J Clin Ortho 1997 : 31 : 763-7
  5. Costa A, Raffaini M, Melsen B. Miniscrews as orthodontic anchorage : A preliminary report. Int Adult Orthod Orthognath Surg 1998 : 13 : 201-9
  6. 박효상. Micro-implant를 이용한 교정치료. 1판.서울 : 나래출판사 : 2001 : 5-22, 187-90
  7. 문철현. SAS의 임상적 적용과 실패의 원인 및 대책. 1판.서울 : 나래출판사 : 2002 : 82-110
  8. Geng JP, Tan KB, Liu GR. Application of finite element analysis in implant dentistry : A review of the literature. J Prosthet Dent 2001 :85 : 585-98
  9. Stegaroiu R, Sato T, Kusakari H. Influence of restoration type on stress distribution in bone around implants : A three-dimensional finite element analysis. Int J Oral Maxillofac Implants 1998 : 13 : 82- 90
  10. 경승현, 임중기, 박영철. Miniscrew를 고정원으로 이용한 교정치료. 대치교정지 2001 : 31 : 415-24
  11. 유남재, 박병수, 정길수, 김진황. 풍화암에 근입된 영구 앵커의 극한인발력. 강원대학 교산업기술연구소 논문집 2001 : 21 : 195-203
  12. Chaconas SJ, Caputo AA, Davis JC. The effects of orthopedic forces on the craniofacial complex utilizing cervical and headgear appliances. Am J Orthod Dentofac Orthop 1976 : 69 : 527-39
  13. 김충배, 양원식. Laser holography를 이용한 상악 headgear 견인에 따른 안면두개골의 초기반응에 관한 연구. 대치교정지 1986 : 16 : 31-41
  14. Bratcher HJ, Muhl ZF, Randolph RG. Clinical measurement of distally directed headgear loading. Am J Orthod Dentofac Orthop 1985 : 88 : 125-32
  15. Vasquez M, Calao E, Becerra F et. al. Initial stress difference between sliding and sectional mechanics with an endosseous implant as anchorage : A 3-dimensional finite element analysis. Angle Orthod 2001 : 71 : 247-56
  16. 이봉훈. 유한요소법 핸드북, 서울 : 도서출판 동화기술, 1991
  17. Misch CE. 최신 임플란트 치과학. 2판.서울 : 나래출판사 : 2000 : 311-49
  18. 윤병수, 최병호, 이원유 등 성견에서 교정적 고정원으로서의 티타늄 미니스크류에 대한 연구. 대치교정지 2001 : 31 : 517-23
  19. Rieger M, Mayberry M, Brose MO. Finite element analysis of six endosseous implants. J Prosthet Dent 1990 : 63 : 671-6