Structural Engineering and Mechanics

Techno-Press (테크노프레스)
권호 표지
DOI QR코드

DOI QR Code

Thermomechanical analysis of the tensile test: simulation and experimental validation

  • Celentano, Diego J. (Departamento de Ingenieria Mecanica, Universidad de Santiago de Chile)
  • Received : 2001.02.12
  • Accepted : 2002.03.20
  • Published : 2002.06.25
⟨ Previous Next ⟩

Abstract

This paper presents experimental and numerical analyses of the thermomechanical behaviour that takes place in SAE1020 mild steel cylindrical specimens during the conventional tensile test. A set of experiments has been carried out in order to obtain the stress-strain curve and the diameter evolution at the neck which allow, in turn, to derive the elastic and hardening parameters characterizing the material response. Temperature evolutions have also been measured for a high strain rate situation. Moreover, a finite element large strain thermoelastoplasticity-based formulation is proposed and used to simulate the deformation process during the whole test. Some important aspects of this formulation are discussed. Finally, the results provided by the simulation are experimentally validated.

Keywords

References

  1. Annual Book of ASTM Standards (1988), Section 3: Metals Test Methods and Analytical Procedures.
  2. Armero, F. and Simo, J. (1993), "A priori stability estimates and unconditionally stable product formula algorithms for non-linear coupled thermoplasticity", Int. J. Plasticity, 9, 149-182.
  3. Bridgman, P. (1952), Studies in Large Plastic and Fracture, McGraw-Hill Book Company, London.
  4. Celentano, D., Gunasegaram D. and Nguyen T. (1999), "A thermomechanical model for the analysis of light alloy solidification in a composite mould", Int. J. Solids and Struct., 36, 2341-2378. https://doi.org/10.1016/S0020-7683(98)00114-0
  5. Celentano, D. (2001), "A large strain thermoviscoplastic formulation for solidification of S.G. cast iron in a green sand mould", Int. J. Plasticity, 17, 1623-1658. https://doi.org/10.1016/S0749-6419(00)00095-4
  6. Coleman, B. and Gurtin, M. (1967), "Thermodynamics with internal state variables", J. Chem. Phys., 47(2), 597-613. https://doi.org/10.1063/1.1711937
  7. Crisfield, M. (1991), Non-linear Finite Element Analysis of Solids and Structures, 1-2. John Wiley & Sons, Chichester.
  8. Dieter, G. (1988), Mechanical Metallurgy - SI Metric Edition, McGraw-Hill Book Company, London.
  9. Doyle, T. and Ericksen, J. (1956), "Nonlinear elasticity", Adv. Appl. Mech., 4.
  10. García Garino, C. and Oliver, J. (1993), "A numerical model for elastoplastic large strain problems", Fundamentals and applications, Proc. COMPLAS III, 117.
  11. Goicolea, J., Gabaldón, F. and García Garino, C. (1996), "Analysis of the tensile test using hypo and hyperlastic models (in Spanish)", Proc. III Congress on Numerical Methods in Engineering, 875-885.
  12. Lubliner, J. (1990), Plasticity Theory, Macmillan Publishing.
  13. Malvern, L. (1969), Introduction to the Mechanics of a Continuous Medium, Prentice-Hall, Englewood Cliffs.
  14. Nadai, A. (1950), Theory of Flow and Fracture of Solids, McGraw-Hill Book Company, London.
  15. Simo, J. and Armero, F. (1992), "Geometrically non-linear enhanced strain mixed methods and the method of incompatible modes", Int. J. Numer. Meth. Eng., 33, 1413-1449. https://doi.org/10.1002/nme.1620330705
  16. Simo, J. (1995), Topics on the Numerical Analysis and Simulation of Plasticity, Handbook of Numerical Analysis, Vol. III, Elsevier Science Publishers.
  17. Wriggers, P., Miehe, C., Kleiber, M. and Simo, J. (1989), "On the coupled thermo-mechanical treatment of necking problems via finite-element-method", Proc. COMPLAS II, 527-542.
  18. Zerilli, F. and Armstrong, W. (1987), "Dislocation-mechanics-based constitutive relations for material dynamics calculations", J. Appl. Phys., 61(5), 1816-1825. https://doi.org/10.1063/1.338024
  19. Zienkiewicz, O. and Taylor, R. (1989), The Finite Element Method, 4th Edition, 1-2. McGraw-Hill, London.

Cited by

  1. Analysis of the Bridgman Procedure to Characterize the Mechanical Behavior of Materials in the Tensile Test: Experiments and Simulation vol.72, pp.1, 2005, https://doi.org/10.1115/1.1827243
  2. Thermomechanical Simulation and Experimental Validation of Wire Drawing Processes vol.25, pp.7, 2010, https://doi.org/10.1080/10426910903180003
  3. Experimental and Numerical Analysis of Low Output Power Laser Bending of Thin Steel Sheets vol.134, pp.3, 2012, https://doi.org/10.1115/1.4005807
  4. Characterization of the mechanical behaviour of materials in the tensile test: experiments and simulation vol.12, pp.4, 2004, https://doi.org/10.1088/0965-0393/12/4/S09
  5. Effect of workpiece geometry using circular scan patterns in sheet laser forming processes vol.96, pp.5-8, 2018, https://doi.org/10.1007/s00170-018-1628-3