DOI QR코드

DOI QR Code

Three-dimensional cure simulation of composite structures by the finite element method

유한요소법을 이용한 복합재 구조물의 3차원 경화 수치모사

  • 민경재 (건국대학교 항공우주공학과 대학원) ;
  • 박훈철 (건국대학교 기계항공공학부) ;
  • 윤광준 (건국대학교 기계항공공학부)
  • Published : 2002.09.30

Abstract

In this paper, a finite element formulation was introduced for the three-dimensional cure simulation of composite structures. Based on the formulation, a three-dimensional finite element code was developed. Numerical examples found in the literatures were solved for code verification. Results from the present analyses agreed well with the measured cure-induced temperatures. Unlike in one or two dimensional analysis, temperature and degree of cure were able to be calculated at any point within composite structures in the present analysis. The finite element program can be used for the cure simulation of composite structures with arbitrary geometry under non-uniform autoclave temperature distribution.

본 논문에서는 복합재의 3차원 경화 수치모사를 위해 유한요소 정식과정을 제시하였다. 이 정식을 기초로 하여 유한요소 프로그램을 개발하였다. 개발한 프로그램을 검증하기 위해 참고문헌에 제시된 수치예제에 대한 해석을 수행하였다. 본 논문에서의 경화 수치모사결과가 측정된 경화온도와 잘 일치하였다. 본 3차원 경화 수치모사에서는 1, 2차원 해석과는 달리 복합재 구조물의 임의 지점에서의 수치모사 결과분석이 가능하다. 개발된 유한요소 프로그램을 이용하면 불규칙한 형상을 가진 복합재 구조물과 일정하지 않은 오토클레이브 내부 온도분포 하에서의 경화 수치모사를 할 수 있다.

Keywords

References

  1. H.J. Carala, "Structural Evaluation of 8-in Diameter Graphite-Epoxy Composite Cylinders Subjected to external Hydrostatic Compressive Loading," DTRC-89/016 David Taylor Research Center, 9/1989.
  2. S.Y. Lee and G.S. Springer, "Filament Winding Cylinders: I. Process Model," Journal of Composite Materials, Vol. 24, 12/1990.
  3. E.P. Calius, S.Y. Lee and G.S. Springer, "Filament Winding Cylinders: II. Validation of the Process Model," Journal of Composite Materials, Vol. 24, 12/1990.
  4. S.Y. Lee and G.S. Springer, "Filament Winding Cylinders: III. Selection of the Process Variables," Journal of Composite Materials, Vol.24, 12/1990.
  5. T.A. Bogetti and J.W. Gillespie, JR., "Two-Dimensional Cure Simulation of Thick Thermosetting Composites," Journal of Composite Materials, Vol.25, pp. 239-273, 1991. https://doi.org/10.1177/002199839102500302
  6. S.R. White and H.T. Hahn, "Cure Cycle Optimization for the Reduction of Processing -Induced Residual Stresses in Composite Materials," Journal of Composite Materials, Vol. 27, No.14, 1993.
  7. P.R. Ciriscioli, G. S. Springer and W.I. Lee, "An Expert System for Autoclave Curing of Composites," Journal of Composite Materials, Vol.25, 12/1991.
  8. C. Kim, H. Teng, C. L. Turcker and S.R. White, "The Continuous Curing Process for Thermoset Polymer Composites. Part 1: Modeling and Demonstration," Journal of Composite Materials, Vol.29, No.9, 1995.
  9. 박훈철, "유한요소법에 의한 복합재 구조물의 성형 수치모사" 한국항공우주학회지 제25권 제6호, pp.104-109, 1997.
  10. Sung Yi, H.H. Hinton and M.F. Ahmad, "A finite element approach for cure simulation of thermosetting matrix composites," Computers and Structures, Vol. 64, No.1-4, pp.383-388, 1997. https://doi.org/10.1016/S0045-7949(96)00156-3