Effect of Ball End Mill Geometry and Cutting Conditions on Machinability of Hardened Tool Steel

  • Jang, Dong-Y. (Industrial Information Systems Engineering Department, Seoul National University of Technology) ;
  • Won, S.-T. (Die & Mold Design Department)
  • Published : 2002.06.01

Abstract

Roughing of tool steel in its hardened state represents a real challenge in the die and meld industry and process improvement depends on research of tool material, coating technique, and lubrication. However, roughing of hardened steels generates extreme heat and without coolant flooding, tool material cannot withstand the high temperature without choosing the right tools with proper coating. This research conducted milling tests using coated ball end mills to study effects of cutting conditions and geometric parameters of ball end mills on the machinability of hardened tool steel. KP4 steel and STD 11 heat treated steels were used in the dry cutting as the workpiece and TiAIN coated ball end mills with side relief angle of 12$^{\circ}$ was utilized in the cutting tests. Cutting forces, tool wear, and surface roughness were measured in the cutting tests. Results from the experiments showed that 85 m/min of cutting speed and 0.32 mm/rev of feed rate were optimum conditions for better surface finish during rough cutting and 0.26mm/rev with the same cutting speed are optimum conditions in the finish cutting.

Keywords

References

  1. Stovicek, D., 'Hard Pan Turning,' Tooling & Production, 57, pp. 25-26 (1992)
  2. El-Wardany, T. I., Mohamed, E. and Elbestawi. M. A., 'Material Side Flow in Finish Turning of Hardened Steel with Ceramic Tools' Contact Problems anc Surface Interaction in Manufacturing and Tribological Syitem, ASME, Ped-Vol. 67/Trib-Vol. 4, pp. 159-170 (1993)
  3. Jang, D. Y, Choi, Y, Kim, H. and Hsiao, Y., 'Study of Correlation Between Surface Roughness and Cutting Vibrations to Develop an On-line Roughness Measuring Technique in Hard Tuming,' International Journal of Machine Tools & Manufacture, 36, 4, pp. 453-464 (1996) https://doi.org/10.1016/0890-6955(95)00074-7
  4. Diniz, A. E., Liu, J. J. and Domfeld, D. A., 'Correlating Tool Life, Tool Wear, and Surface Roughness by Monitoring Acoustic Emission in Finish Tuming,' Wear, 118, pp. 395-406 (1992)
  5. Carius, A., and Rigby, R, 'PCBN Tums the Ha-d Stuff,'Cutting Tool Engineering, 47, 4, pp. 24-32 (1995)
  6. Noaker, P. M., 'Hard Tuming Heats Up,' Manafacturing Engineering, pp. 47- 50 (1995)
  7. Brandt, G., 'Flank and Crater Weai Mechanisms of AluminaBased Cutting Tools When Machining Steel,' Wear. 112, pp. 39-56 (1986) https://doi.org/10.1016/0043-1648(86)90199-7
  8. T$\ddot o$nshoff, H. K., Wobker, H. G. and Brandt, D., 'Tribological Aspects of Hard Turning With Ceramie Tools,' Lubrication Engineering, 51, 2, pp. 63-168 (1994)
  9. Singh, R., Coldwell, H. L.. Aspinwall, D. K. and Dews, R. C., 'High Speed Milling if Hardencd Steel Moulds and PressTools,' Proceedings of $33^{rd}$ International MATADOR Conf., pp. 427-432(2000)
  10. R. C. Dewes etal, 'High Speed Machining of Hardened Steel using Coated Tungsten Cai-bide Ball Nose End Mills,' 2nd Int. Conference on High Speed Machining, pp. 165-174(1999)
  11. R. C. Dewes etal, 'The Use of High Speed Machining for the Manufacture of Hardened Steel Dies,' Transactions of the NAMRI of SME, 25, pp. 21-26(1966)
  12. M. A Elbestawi etal, 'High-Speed Milling of Dies and Moldsin their Hardened State', Annals of the CIRP, 46(1), pp. 57--62 (1997) https://doi.org/10.1016/S0007-8506(07)60775-6