A Study on the Injection Molding Process for Manufacturing of Alternator Pulley

얼터네이터 풀리의 제조를 위한 사출성형공정에 관한 연구

  • 민병현 (동의대학교 기계·산업시스템공학부) ;
  • 김영호 (부산대학교 기계공학과)
  • Published : 2002.05.01

Abstract

So far, an alternator pulley has been formed by cold forging and casting with a metal due to the necessity of its high strength. Various advantages such as the light weight, the low cost, and the high productivity can be obtained by the injection molding process using engineering plastics. Engineering plastics have an excellent performance in the characteristics off strength vs. weight, a good forming ability and a productivity. The object of this study is to develop an alternator pulley, which has been made with a metal, using the injection molding process based on Taguchi methods. A sink mark is considered as a characteristic parameter to improve the quality. The FEM Simulation CAE tool, Moldflow, is used for the analysis of injection molding process.

Keywords

References

  1. 신동명, 자동차재료, 형설출판사, pp.280-312, 1996
  2. 신보성, 최두선, 심국보, 송선호, 백재현, '자동차 엔진 풀리 성형공정설계에 관한 연구,' 한국정밀공학회 춘계학술대회 논문집, pp.630-634, 1997
  3. 김동진, 정덕진, 김병민, 최재찬, '자동차 냉방기용 내부 풀리의 냉간 단조 공정 설계,' 한국자동차공학회 논문집, 제5권 제4호,pp.199-206, 1997
  4. 홍명웅, 사출성형기술 I, 기전연구사, pp.71-94, 1990
  5. H. Naka, I. Takashi, K. Kazuei, 'Prediction of Sink Marks in Injection-Molded Plastic Parts using a Localized Shrinkage Analysis near a Rib,' JSME International Journal, Vol.30, No.265, 1987
  6. M. J. Liou, D. M. Ramachandra, K. Ishii, L. Hornberger, 'Sink Mark Study in Injection Molded Parts,' ANTEC '90, pp.288-291, 1997
  7. G. Taguchi, Introduction to Quality Engineering, American Supplier Institute, Michigan, 1987
  8. Q. Zou, G. Ari, R. Hess, 'Using DOE Techniques on Molding Simulation to Improve Injection Molded Part Quality,' ANTEC '96, pp.736-743, 1996
  9. Y. S. Zu, S. T. Lin, 'Optimizing the Mechanical Properties of Injection Molded W-4.9% Ni-2.1% Fe in Debinding,' Journal of Materials Processing Technology, Vol.71, No.2, pp.337-342, 1997 https://doi.org/10.1016/S0924-0136(97)00095-2
  10. S. H. Dillman, D. Howe, H. Robar, 'Optimization of the Injection Molding Process,' ANTEC '96, pp.754-758,1996
  11. S. E. Barbosa, J. M. Kenny, 'Effects of Processing Conditions on the Microstructure of Polypropylene and its Short Fiber Composites,' ANTEC '96, pp.2246-2255, 1996
  12. RTP C. O., Company Data Sheet, Floppy Diskette, Ver.3.0, 1999
  13. 박성현, 응용실험계획법, 영지문화사, pp.175-195,1990
  14. 박성현, 현대실험계획법, 민영사, pp.631-657, 1984