초록
상아질접착제의 광조사가 상아질접착에 미치는 영향을 알아보기 위하여 in vitro에서 접착실험을 하였다. 120개의 발거된 소의 전치 협면 상아질을 노출시키고 산 부식 한 다음 self-priming형 상아질접착제 Prime&Bond$^{\circledR}$NT (Dentsply DeTrey, GmbH, Konstanz, Germany)를 도포 하였으며 600 mW/$\textrm{cm}^2$의 일반광도 또는 1930 mW/$\textrm{cm}^2$의 초고광도 광조사를 각각 20초 및 3초간 시행한 군과 시행하지 않은 군으로 나누어 복합레진 첨가후 광조사하였다. 접착제에 대한 광조사를 시행하지 않은 경우에는 복합레진 첨가 후 초고광도로 3초, 6초 및 12초간 광조사하였다. 접착양상 평가를 위해 만능시험기로 전단접착강도를 측정하고 파단면을 입체 현미경으로 관찰한 바를 일원 및 이원 변량분석법과 카이제곱검사법으로 통계 분석하여 다음과 같은 결과를 얻었다. 1. 상아질접착제를 광조사한 군이 광조사하지 않은 군에 비해 유의하게 높은 전단접 착강도를 나타내었다 (p<0.05). 2. 일반 광도 및 초고광도 광조사에 따른 전단접착강도에는 유의한 차이가 나타나지 않았다 (p>0.05). 3. 상아질접착제를 광조사하지 않고 복합레진 첨가 후 초고광도로 광조사한 군간에 조사시간에 따른 전단접착강도에는 유의 한 차이가 나타나지 않았다 (p>0.05). 4. 파단면 관찰 결과, 모든 군에서 접착계면에서의 파절을 포함하는 혼합파단양상이 가장 많이 나타났으며 군간에는 유의한 차이가 없었다 (p>0.05).
The purpose of this study was to investigate the influence of light irradiation over self-priming adhesive on dentin bonding. After acid etching the exposed dentin, a self-priming adhesive (Prime&Bond$^{\circledR}$NT dental adhesive system Dentsply DeTrey, GmbH, Konstanz, Germany) was applied and light irradiation was done for 20 sec with regular intensity (600 mW/$\textrm{cm}^2$) in group I and for 3 sec with ultra-high intensity (1930 mW/$\textrm{cm}^2$) in group III. No light irradiation was done over self-priming adhesive in groups II and IV. Composite resin was added on the self-priming adhesive and irradiated for 40 sec with regular intensity (600 mW/$\textrm{cm}^2$) in groups I and II and for 3 sec with ultra-high intensity (1930 mW/$\textrm{cm}^2$) in groups III and IV. To see the effect of light curing time on dentin bonding, another 3 group specimens were prepared. Without light-irradiation over self-priming adhesive, added composite resin was irradiated for 3, 6, or 12 sec with ultra-high intensity light. After bonded specimens were stored in 37$^{\circ}C$ distilled water for 24 hours, shear bond strength were measured using a universal testing machine (4202, Instron, Instron Co., U.S.A.) and fractured surfaces were examined under a stereomicroscope (SZ-PT Olympus, Japan). Statistical analysis were done with one-way, two-way ANOVA and chi-square test. The results were as follows : 1. The shear bond strengths from the groups irradiated over self-priming adhesive were significantly higher than those from the groups without irradiation (p<0.05). 2. There was no significant shear bond strength difference between regular intensity light irradiation groups and ultra-high intensity ones (p>0.05). 3. There was no significant shear bond strength difference among various irradiation time groups with ultra-high intensity ones (p>0.05). 4. In stereomicroscopic examination of fractured surfaces, adhesive-cohesive mixed failure mode was mostly seen in all groups, and there was no significant difference in failure mode among groups (p>0.05).
