Applications of Cure Monitoring Techniques by Using Fiber Optic Strain Sensors to Autoclave, FW and Rm Molding Methods

  • Fukuda, Takehito (Department of Intelligent Materials Engineering, Osaka City Unv) ;
  • Kosaka, Tatsuro (Department of Intelligent Materials Engineering, Osaka City Unv) ;
  • Osaka, Katsuhiko (Department of Intelligent Materials Engineering, Osaka City Unv)
  • 발행 : 2001.12.01

초록

This paper describes applications of cure monitoring techniques by using embedded fiber optic strain sensors, which are extrinsic Fabry-Perot interoferometric (EFPI) and/or fiber Bra99 grating (FBG) sensors, to three kinds of molding methods of autoclave, FW and RTM molding methods. In these applications, internal strain of high-temperature curing resin was monitored by EFPI sensors. From theme experimental results, it was shown that strain caused by thermal shrink at cooling stage could be measured well. In addition, several specific matters to these molding methods were considered. As thor an autoclave molding of unidirectional FRP laminates, it was confirmed that off-axis strain of unidirectional FRP could be monitored by EFPI sensors. As for FW molding using room-temperature (RT) cured resin, it was found that the strain outputs from EFPI sensors represented curing shrinkage as well as thermal strain and the convergence meant finish of cure reaction. It was also shown that this curing shrinkage should be evaluated with consideration on logarithmic change in stiffness of matrix resin. As for a RTM melding, both EFPI and FBC sensors were employed to measure strain. The results showed that FBG sensors hale also good potential for strain monitoring at cooling stage, while the non-uniform thermal residual strain of textile affected the FBG spectrum after molding. This study has proven that embedded fiber optic strain sensors hale practical ability of cure monitoring of FRP. However, development of automatic installation methods of sensors remains as a problem to be solved for applications to practical products.

키워드

참고문헌

  1. Materials Science Research International- Special Technical Publication v.2 Smart Monitoring Techniques for Composites Molding Processes T. Fukuda;T. Kosaka
  2. 12th International Conference on Composite Materials (ICCM-12), Pap1260.pdf (PDF file) Development of Multi-Functional Sensor for Resin Transfer Molding S. Motogi;T. Itoh;T. Fukuda;K. Yamagishi;S. Kitade;H. Morita
  3. Smart Materials and Structures v.7 In-Situ Cure Monitoring Using Optical Fibre Sensors - A Comparative Study G.R. Powerll;P.A. Crosby;D.N. Waters;C.M. France;R.C. Spooncer;G.F. Fernando
  4. Smart Materials and Structures v.5 In Situ Cure Monitoring of Epoxy Resins Using Optical Fibre Sensors P.A. Crosby;G.R. Powerll;G.F. Fernando;C.M. France;R.C. Spooncer;D.N. Waters
  5. Polymer Engineering and Science v.34 no.12 Fiberoptic Intrinsic Fluorescence for In-Situ Cure Monitoring of Amine Cured Epoxy and Composites H.J. Paik;N.H. Sung
  6. Plastics Engineering v.51 no.10 Plastics Analysis: Cure Monitoring in RTM Using Fluorescence D.L. Woerdenman;R.S. Parnas
  7. Journal of Composite Materials v.31 no.1 Fiber optic sensor development for real-time in-situ epoxy cure monitoring Y.M Liu;C. Ganesh;J.P.H. Steele;J.E. Jones
  8. Smart Materials and Structures v.4 Processing monitoring of carbon/phenolic composites using smart snesors L. Lai;G. Carman;S.Chiou;P. Kukuchek;D. Echternach
  9. Proc SPIE v.3670 Embedded Fiber Optic Sensor Arrays for Structural Health Monitoring of Filament Wound Composite Pressure Vessels R.C. Foedinger;D.L. Rea;J.S. Sirkis;C.S. Baldwin;J.R. Troll
  10. Proc. SPIE v.3670 Multi-Functional Fiber Optic Sensors for Cure and Temperatur Monitoring P.A. Crosby;C.Doyle;C. Tuck;M. Singh;G.F. Fernando
  11. Materials Science Research International-Special Technical Publication v.2 Curing Strain Monitoring of FRP FW Pipe with EFPI Fiberoptic Sensors T. Kosaka;K. Osaka;M. Sando;T. Fukuda
  12. Materials Science Research International-Special Technical Publication v.2 Off-axis Strain Monitoring of FRP Laminates in Autoclave Molding K. Osaka;T. Kosaka;Y. Asano;T. Fukuda
  13. Proc. of the 13th International Conference on Composite Materials (ICCM-13), pcd1611(PDF) Cure Monitoring of FRP by FBG Fiberoptic Sensors in RTM Molding Process T. Kosaka;K. Osaka;Y. Asano;T. Fukuda
  14. Proc. of the 7th Japan International SAMPE Symposium Development of Smart Braided Composites by Using Fiberoptic Strain Sensors T. Kosaka;H. Kurimoto;K. Osaka;A. Nakai;lT. Osada;H. Hamada;T. Fukuda
  15. Composites v.30 The Use of Fabry Perot Fiber Optic Sensors to Monitor Residual Strains during Pultrusion of FRP Composites A.L. Kalamkarov;S.B. Fitzgerald;D.O. MacDonald
  16. Proceedings of The 2nd Korea-Japan Joint Symposium on Composite Materials Cure Monitoring of Composite Laminates Using Fiber Optic Sensors H,K, Kamg;D.H. Hang;C.S. Hong;C.G. Kim
  17. Sensors and Actuators: A v.79 Cure Monitoring of Smart Composites Using Fiber Bragg Grating Based Embedded Sensors V.M. Murukeshan;P.Y. Chan;L.S. Ong;L.K. Seah
  18. Optic Letters v.18 White-Light Interferometric Multimode Fiber-Optic Strain Sensor C. Belleville;G. Duplain
  19. Optics and Lasers in Engineering v.31 Recent Progress in Applications of In-Fibre Bragg Grating Sensors Y.J. Rao
  20. Proc. SPIE v.3670 Measurement of Stress Concentrations Using Embedded Optical Fiber Bragg Grating Sensors K.J. Peters;M. Studere;J. Botsis;A. locco;H.G. Limberger;R.P. Salathe
  21. Smart Materials and Structures v.9 no.6 Detection of Transverse Cracks in CFRP Composites Using Embedded Fiber Bragg Grating Sensors Y. Okabe;S. Yashiro;T. Kosaka;N. Takeda
  22. Journal of the Society of Materials Science v.24 no.257 Elastic Constants of Carbon Fiber Reinforced Plastic Materials M. Uemura;N. Yamada