Modeling of High-speed Tapping Touque Considering Friction Force

마찰력을 고려한 고속탭핑 토크 모델링

  • 이돈진 (부산대 지능기계공학과) ;
  • 강지웅 (부산대 지능기계공학과) ;
  • 전현배 (부산대 지능기계공학과) ;
  • 김선호 (한국기계연구원 자동화연구부) ;
  • 안중환 (부산대 기계공학부)
  • Published : 2001.11.01

Abstract

This paper aims at developing a torque model for the high-speed tapping with small-diameter taps. As recent industries such as automobile and information technology grows, taps smaller than 5mm in diameter are needed much more. In that occasion, the friction force between a tap surface and a workpiece plays much more important role in the tapping torque than in he larger tapping. Tapping mechanism was analysed based on the tap geometry. It has two steps : one is a forward cutting composed of the chamfered threading and full threading and the other is the backward cutting. The torque by the cutting force in the chamfered threading is calculated using the cutting area and the specific cutting force while the torque by the friction force, which is rather dominant than the cutting force both in the full threading and in the backward cutting, is calculated using the normal force on the threads and the friction coefficient. The experiment has shown that the results by the proposed torque model fit quite well with the acutal measurements within the error of 10%.

Keywords

References

  1. Lorenz. G, 'The Effect of Rake Angle in Nut Tapping,' C.I.R.P. annals, Vol. 12, pp. 116-119, 1963
  2. Lorenz. G, 'A Study on the Effect of Tap Geometry,' Mech. Eng. Transaction, Inst. Eng., Australia, Me, Vol. 3, pp. 101-104, 1978
  3. G. Lorenz, 'On Tapping Torque and Tap Geometry,' C.I.R.P. annals, Vol. 29, No. 1, pp. 1-4, 1980
  4. E.D.Doyle, D.K.Dean, 'Effect of Axial Forces on Dimensional Accuracy during Tapping,' Int. J. Mach. Tool Des. Res., Vol. 14, pp. 325-333, 1974 https://doi.org/10.1016/0020-7357(74)90021-3
  5. 최만성, '고속탭핑에 있어서 절삭토크에 관한 연구,' 대한기계학회논문집, 제18권 12호, pp. 3195-3201, 1994
  6. 최만성, 송지복, '고속태핑에 있어서 탭의 형상과 절삭토크의 특성,' 한국정밀공학회지, 제13권 8호, pp. 139-145, 1996
  7. 이정길, 최만성, 'STS304의 태핑과 탭 형상에 관한 연구,' 한국정밀공학회지, 제17권 11호, pp. 55-68, 2000
  8. 한국 OSG, '태핑작업 Technical Data,' 한국 OSG, pp. 12-15, 1990
  9. 신정식, 김찬호, 안중환, 김화영, 김선호, '고속 탭핑의 가공상태 감사시스템(I)-탭 형상에 기초한 절삭토크 시뮬레이션,' 대한기계학회 학술대회 논문집(A) pp. 1074-1078, 1999
  10. 김하룡 역, '구멍가공용 공구의 모든 것,' 성안당, 1996