대한기계학회논문집A (Transactions of the Korean Society of Mechanical Engineers A)

  • 제24권11호
  • /
  • Pages.2680-2687
  • /
  • 2000
  • /
  • 1226-4873(pISSN)
  • /
  • 2288-5226(eISSN)
대한기계학회 (The Korean Society of Mechanical Engineers)
권호 표지
DOI QR코드

DOI QR Code

공동현상을 고려한 소형 정밀 모터용 빗살무늬 저널베어링의 해석

Analysis of a Hydrodynamic Herringbone-Grooved Journal Bearing in a Small Precision Motor Considering Cavitation

  • 창동일 (한양대학교 대학원 정밀기계공학과) ;
  • 장건희 (한양대학교 기계공학부)
  • 발행 : 2000.11.01
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

The Reynolds equation, incorporating Elrods cavitation algorithm, is discretized on a rectangular grid in computational space through coordinate mapping in order to accurately analyze a herringbone grooved journal bearing of a spindle motor in a computer hard disk drive. The pressure distribution and cavitation area are determined by using the finite volume method. Predicted results are compared to experimental data of previous researchers. It was found that positive pressure is developed within the converging section of the bearing and that a cavity occurs in the diverging section. Cavitation has been neglected in the previous analysis of the herringbone grooved bearing. Load capacity and bearing torque are increased due to the increased of eccentricity and L/D and the decrease of the grooved width ratio. The maximum load capacity was found to occur at a groove angle of 30 degrees while bearing torque remains constant due to the variation of the groove angle. The cavitation region is significantly decreased with the inclusion of herringbone grooves. However, the region increases with the increase of the eccentricity, L/D, groove angle and the rotational speed and the decrease of the grooved width ratio.

키워드

참고문헌

  1. Bouchard, G., Lau, L., and Talk, F. E., 1987, 'An Investigation of Nonrepeatable Spindle Runout,' IEEE Transactions on Magnetics, Vol. 23, No. 5, pp. 2760-2762
  2. Vijayaraghavan, D. and Keith, Jr. T. G, 1989, 'Development and Evaluation of a Cavitation Algorithm,' STLE Tribology Transactions, Vol. 32, pp. 225-233 https://doi.org/10.1080/10402008908981882
  3. Jakobsson, B., and Floberg, L., 1957, 'The Finite Journal Bearing Considering Vaporization,' Charmers Tekniska Hoegskolas Handlingar, Vol. 190, pp. 1-116
  4. Olsson, K. G., 1965, 'Cavitation in Dynamically Loaded Bearings,' Chalmers University of Technology, Goteborg
  5. Elrod, H. G. and Adams, M. L., 1974, 'A Computer Program for Cavitation and Starvation Program,' Cavitation and Related phenomena in Lubrication, Mechanical Engineering Publication, New York, pp. 33-41
  6. Elrod, H. G., 1981, 'A Cavitation Algorithm,' ASME Journal of Lubrication Technology, Vol. 103, pp. 350-354
  7. Savage, M. D., 1985, 'The Zero Pressure Gradient Condition,' ASME Journal of Tribology, Vol. 107, pp. 252-255
  8. Brewe, D. E., 1986, 'Theoretical Modeling of the Vapor Cavitation in Dynamically Loaded Journal Bearings,' ASME Journal of Lubrication Technology, Vol. 108, pp. 628-638
  9. Vijayaraghavan, D. and Keith, Jr. T. G, 1990a, 'An Efficient, Robust, and Time Accurate Numerical Scheme Applied to a Cavitation Algorithm,' ASME Journal of Tribology, Vol. 112, pp. 44-51
  10. Vijayaraghavan, D. and Keith, Jr. T. G, 1990b, 'Grid Transformation and Adaption Techniques Applied to the Analysis of Cavitated Journal Bearings,' ASME Journal of Tribology, Vol. 112, pp. 52-59
  11. Bootsma, J., 1975, 'Liquid-Lubricated Spiral-Groove Bearings,' Phillips Research Reports-Supplements, No. 7, The Netherlands
  12. Zang, Y. and Hatch, M. R., 1995, 'Analysis of Coupled Journal and Thrust Hydrodynamic Bearing using Finite-Volume Method,' ASME Advances in Information Storage and Processing System, Vol. 1, pp. 71-79
  13. Rahman, M. and Leuthold, H., 1996, 'Computer Simulation of a Coupled Journal and Thrust Hydrodynamic Bearing using a Finite Element Method,' ASME AISPS, Vol. 2, p. 103
  14. Jang, G. H. and Kim. Y. J., 1999, 'Calculation of Dynamic Coefficients in a Hydrodynamic Bearing Considering Five Degrees of Freedom for a General Rotor-Bearing System,' ASME Journal of Tribology, Vol. 121, pp. 499-505
  15. Zirkelback, N. and San Andres L., 1998, 'Finite Element Analysis of Herringbone Groove Journal Bearings: A Parametric Study,' ASME Journal of Tribology, Vol. 120, pp. 234-240
  16. Warming, R. F. and Beam, R. M., 1978, 'An Extension of A-Stability to Alternating Direction Implicit Method,' NASA TM-78537
  17. Morton, K. W. and Mayers, D. F., 1994, 'Numerical Solution of Partial Differential Equations,' Cambridge Univ. Press
  18. Hirs, G. G., 1965,' The Load Capacity and Stability Characteristics of Hydrodynamic Grooved Journal Bearings,' ASLE Transactions, Vol. 8, pp.296-305 https://doi.org/10.1080/05698196508972102