DOI QR코드

DOI QR Code

Effect of lateral restraint on the buckling behaviour of plates under non-uniform edge compression

  • Bedair, Osama K. (Civil Engineering Department, Concordia University)
  • 발행 : 1997.01.25

초록

The paper investigates the influence of lateral restraint on the buckling behaviour of plate under non-uniform compression. The unloaded edges are assumed to be partially restrained against translation in the plane of the plate and the distributions of the resulting forces acting on the plate are shown. The stability analysis is done numerically using the Galerkin method and various strategies the economize the numerical implementation are presented. Results are obtained showing the variation of the buckling load, from free edge translation to fully restrained, with unloaded edges simply supported, clamped and partially restrained against rotation for various plate aspect ratios and stress gradient coefficients. An apparent decrease in the buckling load is observed due to these destabilizing forces acting in the plate and changes in the buckling modes are observed by increasing the intensity of the lateral restraint. A comparison is made between the budding loads predicted from various formulas in stability standards based on free edge translation and the values derived from the present investigation. A difference of about 34% in the predicted buckling load and different buckling mode were found.

키워드

참고문헌

  1. Bedair, O. K. (1996), "Buckling behaviour of plates partially retrained aganinst retation under stress gradjent:, Int. J. Structural Engineering and Mechanics. 4(4), 383-396. https://doi.org/10.12989/sem.1996.4.4.383
  2. Bedair, O. K. (1996), "On the post-buckling behaviour of plates under stress gradient", Int. J. Structural Engineering and Mechanics, 4(4), 397-414. https://doi.org/10.12989/sem.1996.4.4.397
  3. Beedle, L.S.(ed.) (1991), Stability of Metal Structures, a World View, 2nd ed., Structural Stability Research Council, USA.
  4. Bradford, M. A. (1989), "Buckling of longitudinally stiffened plates in bending and compression", Can. J. Civ. Eng., 16, 607-614. https://doi.org/10.1139/l89-095
  5. Bulson, P. S. (1967), "Local stability and strength of structural sections", Thin Walled Structures, Chatto & Windus, England. 208-247.
  6. Column Research Committee of Japan (1971), Handbook of Structural Stability, Corona Publishing Co., Tokyo.
  7. Galambos, T. V. (1988), Guide to Stability Design Criteria for Metal Structures, 4th ed., Structural Stability Research Council, John Wiley & Sons, New York.
  8. Gaylord, E. H. and Gaylord, C. N. (1990), Structural Engineering Handbook, McGraw-Hill, USA.
  9. Johnson, J.H. and Noel, G.R. (1953), "Critical bending stress for flat rectangular plates supported along all edges and elastically restrained against rotation along the unloaded compression edge", J. Aero. Sci., 19, 535-540.
  10. Lau, S. C. W. and Hancock, G. J. (1986), "Buckling of thin flat-walled structures by a spline finite strip method", Thin Walled Structures, 4, 269-294. https://doi.org/10.1016/0263-8231(86)90034-0
  11. Maeda, Y. and Okura, I. (1984), "Fatigue strength of plate girder in bending considering out-of-plane deformation of web", Proc. JSCE, Structural Eng./Earthquake Eng., 1, 149-159.
  12. Okura, I., Yen, B. T. and Fisher, J. W., (1993), "Fatigue of thin-walled plate girders", Structural Engineering International, 1, 39-44.
  13. Rhodes, J. and Harvey, J.M. (1977), "Examination of plate post-buckling behaviour", J. Engrg. Mech., ASCE, 103, 461-478.
  14. Rhodes, J. and Harvey, J. M. (1976), "Plain channel section struts in compression and bending beyond the local buckling load", Int. J. Mech. Sci., 8, 511-519.
  15. Schuette, E. H. and McCulloch, J. C. (1947), "Charts for the minimum weight design of multiweb wings in bending", NACA TN 1323.
  16. Usami, T. (1982), "Post-buckling of plates in compression and bending", J. Struct. Div. ASCE, 108, 591-609.
  17. Walker, A.C. (1968), "Maximum loads for eccentrically loaded thin-walled channel struts", IABSE, 28, 169-181.
  18. Walker, A.C. (1967), "Flat rectangular plates subjected to a linearly-varing edge compressive loading", Thin Walled Structures, 208-247.

피인용 문헌

  1. Buckling of long compression-loaded anisotropic plates restrained against inplane lateral and shear deformations vol.42, pp.5, 2004, https://doi.org/10.1016/j.tws.2003.12.004
  2. Buckling of cross-ply laminates subject to linearly varying compressive loads and in-plane boundary restraints vol.26, pp.2, 2013, https://doi.org/10.1177/0892705711420594
  3. Effect of in-plane boundary restraints on optimal design of skew laminates under buckling loads vol.93, pp.8, 2011, https://doi.org/10.1016/j.compstruct.2011.02.015