Abstract
This research was attempted as one of studies on the strength of mortar added admixtures at different curing temperatures. Variations of curing temperature to. test compressive strength, tensil strength and bending strength were $20^{\circ}C$, $30^{\circ}C$ and $35^{\circ}C$ and these results were summarized as follow : In strength of mortar added briquette ash, the compressive strength was increased: 1.58 percent, the tensile strength 0.96 percent, and the bending strength 1.26 percent compared with standard strength, by increasing one degree of celsius temperature. Also in strength of mortar added fly ash, the compressive strength increased on the average 1.3 percent, the tensile strength 0.99 percent, and the bending strength 1.18 percent at the above conditions. In case of using fly ash as admixture, maximum compressive strengths was attained at the level of 25 percent of fly ash, maximum tensile strength at the level of 20 percent of fly ash, and maximum bending strength at the level of 20 percent of fly ash. In case of using briquette ash, maximum compressive strength was attained maximum strength at 20 percent of the admixture, maximum tensile strength at the level of 15 to 20 percent of admixture and maximum bending strength at the level of 20 percent of admixture. Although addition of briquette ash was less effective in increasing the strength compared with the addition of fly ash, briquette ash might be used as one of admixtures because the control of curing temperature might affect in getting the required practical strength.
양생온도(養生溫度)가 혼화재(混和材)를 사용(使用)한 모르터의 강도(强度)에 미치는 영향(影響)을 조사(調査)키 위해서 양생온도(養生溫度)를 $20^{\circ}C$, $30^{\circ}C$, $35^{\circ}C$로 하여 모르터의 압축(壓縮), 인장(引張), 곡강도시험(曲强度試驗)을 실시(實施)하였고 그 결과(結果)를 요약(要約)하면 다음과 같다. 양생온도(養生溫度) $1^{\circ}C$ 상승(上昇)에 대(對)한 강도증가(强度增加)는 기준강도(基準强度)에 대(對)하여 연탄재첨가시(添加時) 압축강도(壓縮强度)에서 1.58%, 인장강도(引張强度)에서 0.96%, 곡강도(曲强度)에서 1.26% 증가(增加)했다. 동일(同一)한 경우 플라이애쉬 첨가시(添加時) 압축강도(壓縮强度)에서 1.3%, 인장강도(引張强度)에서 0.99%, 곡강도(曲强度)에서 1.18%의 증가(增加)를 나타냈다. 압축강도(壓縮强度)는 플라이애쉬 첨가량(添加量) 25%에서 인장강도(引張强度)는 20%, 곡강도(曲强度)도 20%에서 최대치(最大値)를 나타냈다. 연탄재를 혼합(混合)한 경우 압축강도(壓縮强度)에서 20% 인장강도(引張强度)에서 15~20%, 곡강도(曲强度)에서 20% 첨가(添加)할 때 최대치(最大値)를 나타냈다. 연탄재 첨가(添加)의 경우가 플라이애쉬 첨가(添加)의 경우 보다 저강도(低强度)이나 양생온도(養生溫度)의 조절(調節)로 소요(所要)의 강도(强度)를 얻을수 있기 때문에 혼화재(混和材)로서 개발(開發)할 여지(餘地)가 충분(充分)히 있는 것으로 사료(思料)된다.